• Models
  • Contests
  • Slicer
  • Login
  • Start Here
    thingiverse-iconprintables-iconcults3d-iconmakerworld-iconmyminifactory-icon

    3D GO

    3D ModelsContestsCollectionsSaved ModelsOn a mobile device?

3D GO

Privacy Policy
Cookie domino 3D Printer File Image 1
Cookie domino 3D Printer File Image 2
Cookie domino 3D Printer File Thumbnail 1
Cookie domino 3D Printer File Thumbnail 2

Cookie domino

fns720 avatarfns720

December 11, 2019

printables-icon
DescriptionCommentsTags

Description

A Christmas present from Auckland and Jakarta - now with extra gingerbread recipe!

This is a domino shaped cookie cutter set.

Designed in Autodesk Fusion 360. The design is parametric - d_dot parameter sets the dot diameter and hence the rest of the design.

Design: https://a360.co/2r8gWvC

Print it on the side with support. In this case only the domino dots will need some minimal support.

Print instructions

Gingerbread by pappito

  • 500 g flour
  • 150 g caster sugar
  • 250 g honey
  • 50 g butter
  • 1 tsp ground cinnamon
  • 1 tsp ground cloves
  • 2 tsp baking soda
  • 1 egg

Combine flour, caster sugar, spices and baking soda. Slice the butter into the honey and melt them together in the microwave and mix properly. Combine the melted stuff with the draw ingredient mixture, add the egg and develop into an even dough.
Avoid overkneading - loose the dough with a bit of lukewarm water if it becomes too tough.

Wrap it in cling film and leave it as it is for 12-24 hrs (the more rest the better cookie).

After resting completed stretch the dough to 5-10 mm thick (spread the table first because it will stick), cut the dominoes, mark them with the numbers and bake them in preheated oven on 150 ℃ for ~15 minutes.

Leave them rest for a few minutes. For glazing let them rest for 1-2 days at least.

Decorating

  • 1 egg white
  • 150-200 g caster sugar
  • 8 drops vinegar

Whisk the egg white to a half-hard consistency and start to slowly mix the sugar in it teaspoon by teaspoon, until you reach the thickness what you can load it to a piping bag. (The mix should move slowly from a spoon).

Fill a piping bag with the mixture and decorate the cookies to your taste.

Hungarian version:

Mézeskalács - pappito

  • 500g liszt
  • 150g porcukor
  • 250g méz
  • 50g vaj
  • 1 teáskanál fahéj
  • 1 teáskanál szegfűszeg
  • 2 teáskanál szódabikarbóna
  • 1 tojás

Lisztet, porcukrot, fűszereket és szódabikarbónát keverjük össze. A mézbe kockázzuk bele a vajat és a mikróban melegítsük fel, majd keverjük el az olvadt vajat a mézben. Ezt a híg keveréket öntsük a száraz cuccokra, üssük rá a tojást és gyúrjuk össze.
Nem kell túl keményre gyúrni, ha nagyon összeáll, akkor kis langyos vízzel lazítható.

Ha egyben van minden, akkor 3 réteg folpackba tekerjük be és hagyjuk állni egy napot de minimum 12 órát (hosszabb pihentetés: szebb süti).

Másnap nyújtsuk ki kb. fél-egy cm vastagra (előtte lisztezzük be az asztalt, mert ragadni fog a tészta), vágjuk ki a formákat és 150 ℃-ra előmelegített sütőben süssük meg ~15 percig.

Sütés után a kész figurákat hagyjuk a tepsiben pihenni pár percig. Díszítéshez várjunk legalább 1-2 napot a figurákkal.

Máz

  • 1 tojásfehérje
  • 150-200 g porcukor
  • 8 csepp ecet

Verjük fel félig a tojásfehérjét a pár csepp ecettel, majd lassan, kiskanalanként adagoljuk hozzá a porcukrot addig, amíg habzsák kompatibilis konzisztenciájú masszát nem kapunk (a massza akkor jó állagú, ha lassan válik el a kanálról).

Töltsük meg a habzsákot és firkáljuk össze a nyomi sütijeinket.

License:

Creative Commons — Attribution — Share Alike

Related Models

Cable Corners... keep cables in corners! preview image

Cable Corners... keep cables in corners!

muzz64 profile image

muzz64

30,993

Headset Hanger 2.0 preview image

Headset Hanger 2.0

RMTB profile image

RMTB

16,804

Baby Birth Tag Holder for the wall  preview image

Baby Birth Tag Holder for the wall

Morganja profile image

Morganja

4,007

Universal Filament Filter and Lubricator preview image

Universal Filament Filter and Lubricator

CreativeTools profile image

CreativeTools

26,123

3D4U by Miele Coffee Clip preview image

3D4U by Miele Coffee Clip

3D4U powered by Miele profile image

3D4U powered by Miele

8,679

Haus-Familienaufsteller „Home“ mit Namensschildern preview image

Haus-Familienaufsteller „Home“ mit Namensschildern

Daniel Lippert profile image

Daniel Lippert

713

SHARKZ... Fun Multipurpose Clips / Holders / Pegs with moving jaws that bite! preview image

SHARKZ... Fun Multipurpose Clips / Holders / Pegs with moving jaws that bite!

muzz64 profile image

muzz64

24,680

Mechanical wall clock preview image

Mechanical wall clock

Harald Andersson profile image

Harald Andersson

6,978