Lucky 13 weapon pack

I had a lot of fun making the axe for my Orc warrior skin and decided afterwards that I needed to make a few more weapons. Every weapon in the pictures consists of multiple pieces and requires assembly but I have included a version of each weapon that is either one or two pieces for those who would rather paint their weapons. 

Those one and two piece weapons are 

Gatling Gun.stl
Pistol.stl
Shotgun.stl
Axe.stl
Sword 1 of 2.stl 
Sword 2 of 2.stl

These weapons were designed to be used with the Detailed Simple Grip hands made by Printables user Cromulent.

Assembly is straightforward. If you have any questions, don't hesitate to ask.

SWORD

Pieces you will need:

1. Sword Handle - Dark Brown.stl
2. Sword Hilt - Light Brown.stl
3. Sword Blade 1 - Grey.stl
4. Sword Blade 2 - Grey.stl
5. Sword Insert - Orange.stl

Take Sword Insert - Orange.stl, fit it into Sword Blade 1 - Grey.stl and then snap Sword Blade 2 - Grey.stl on top. Fit each piece of Sword Hilt - Light Brown.stl on Sword Handle - Dark Brown.stl and then combine the completed blade with the completed hilt. See the photo below for reference.

GATLING GUN

Pieces you will need:

1. Gatling Gun Body - Black.stl
2. Gatling Gun Ring - Black.stl     X 2
3. Gatling Gun Barrel - Grey.stl    X 6
4. Gatling Gun Bullets - Yellow.stl

You will need to print six Gatling Gun Barrel - Grey.stl and two Gatling Gun Ring - Black.stl in order to assemble a Gatling Gun. Take each barrel and fit it through the two rings before fitting it into Gatling Gun Body - Black.stl. I found it easiest to fit one barrel at a time through both rings and into the body rather than try to fit all six barrels through one ring before trying the second ring. The Gatling Gun Bullets - Yellow.stl are printed flat but are very flexible and slot into a small hole on the side of the body.

PISTOL

Pieces you will need:

1. Pistol Grip - Black.stl
2. Pistol Skin - White.stl

Super simple. Pistol Skin - White.stl fits onto Pistol Grip - Black.stl as seen in the following picture.

SHOTGUN

Pieces you will need:

1. Shotgun Butt - Light Brown.stl
2. Shotgun Fore-End - Light Brown.stl
3. Shotgun Barrels - Grey.stl

Again, super simple. Shotgun Butt - Light Brown.stl fits into Shotgun Barrels - Grey.stl and then Shotgun Fore-End - Light Brown.stl snaps into place on the bottom barrel.

AXE

Pieces you will need: 

1. Axe Handle Knob - Grey.stl
2. Axe Inscription - Grey.stl
3. Axe Spikes - Grey.stl
4. Axe Head - Grey.stl
5. Axe Handle 1 - Dark Brown.stl
6. Axe Handle 2 - Light Brown.stl
7. Axe Inscription Plates - Red.stl

First thing you need to do is to fit the Axe Inscription Plates - Red.stl into Axe Inscription - Grey.stl as seen in the following photo.

Next, take that inscription piece and fit Axe Head - Grey.stl into the middle and put that to the side for a moment.

Take Axe Spikes - Grey.stl and fit it into Axe Handle 2 - Light Brown.stl as seen below.

Now take the completed axe head and fit it into the axe handle assembly. Start by putting the bottom of the axe head into the axe handle and then swinging the top of the axe head in. See the below photo for reference.

Last thing to do is connect the handle and knob the the finished axe head and you're good to go.