• Models
  • Contests
  • Slicer
  • Login
  • Start Here
    thingiverse-iconprintables-iconcults3d-iconmakerworld-iconmyminifactory-icon

    3D GO

    3D ModelsContestsCollectionsSaved ModelsOn a mobile device?

3D GO

Privacy Policy
Fanatec Formula Shifter Magnets 3D Printer File Image 1
Fanatec Formula Shifter Magnets 3D Printer File Image 2
Fanatec Formula Shifter Magnets 3D Printer File Image 3
Fanatec Formula Shifter Magnets 3D Printer File Image 4
Fanatec Formula Shifter Magnets 3D Printer File Image 5
Fanatec Formula Shifter Magnets 3D Printer File Image 6
Fanatec Formula Shifter Magnets 3D Printer File Image 7
Fanatec Formula Shifter Magnets 3D Printer File Image 8
Fanatec Formula Shifter Magnets 3D Printer File Image 9
Fanatec Formula Shifter Magnets 3D Printer File Image 10
Fanatec Formula Shifter Magnets 3D Printer File Image 11
Fanatec Formula Shifter Magnets 3D Printer File Thumbnail 1
Fanatec Formula Shifter Magnets 3D Printer File Thumbnail 2
Fanatec Formula Shifter Magnets 3D Printer File Thumbnail 3
Fanatec Formula Shifter Magnets 3D Printer File Thumbnail 4
Fanatec Formula Shifter Magnets 3D Printer File Thumbnail 5
Fanatec Formula Shifter Magnets 3D Printer File Thumbnail 6
Fanatec Formula Shifter Magnets 3D Printer File Thumbnail 7
Fanatec Formula Shifter Magnets 3D Printer File Thumbnail 8
Fanatec Formula Shifter Magnets 3D Printer File Thumbnail 9
Fanatec Formula Shifter Magnets 3D Printer File Thumbnail 10
Fanatec Formula Shifter Magnets 3D Printer File Thumbnail 11

Fanatec Formula Shifter Magnets

In3DSpace avatarIn3DSpace

August 20, 2020

printables-icon
DescriptionCommentsTags

Description

Shifter magnets for Fanatec Formula wheels. Available in two variants, 6mm magnets for light actuation, and 8mm magnets for heavy actuation.

Required Hardware:
(4) 6 x 2mm disk magnets OR (4) 8 x 2mm disk magnets
(4) M3 x 5mm countersunk screws

Installation Instructions:

  1. Remove shifter paddles.
  2. Use super glue to attach the magnets to the printed pieces. IMPORTANT: Make sure the magnet polarity is correct so that the printed pieces are attracted to each other. Wait for the glue to dry.
  3. Attach the flat printed piece to the wheel using the countersunk screws.
  4. Put the bent piece in place. The magnets should hold it in place.
  5. Re-install the shifter paddle using the original screws.
  6. Repeat for the other side.

License:

Creative Commons — Attribution — Noncommercial

Related Models

Spinning Tops Orbital Series preview image

Spinning Tops Orbital Series

YSoft_be3D profile image

YSoft_be3D

38,502

Glacier Gauntlet: Milo's Challenge, a printable game! no supports, built-in springs preview image

Glacier Gauntlet: Milo's Challenge, a printable game! no supports, built-in springs

Nat profile image

Nat

230

Mini Pocket Sized Fidget Infinity Cube preview image

Mini Pocket Sized Fidget Infinity Cube

HeatherMacAnanny profile image

HeatherMacAnanny

1,485

Micro Catapult preview image

Micro Catapult

LukeTansell profile image

LukeTansell

36,977

Jedovatý meč (V.01) - Metin 2 - Sword from game preview image

Jedovatý meč (V.01) - Metin 2 - Sword from game

Gampi profile image

Gampi

21

Ultimate Toothpick Crossbow V2 preview image

Ultimate Toothpick Crossbow V2

Sairae profile image

Sairae

485

Spirograph preview image

Spirograph

3Domas profile image

3Domas

26,832

Greed on the Grill: A 3D Printed Food Stacking Ballance Game preview image

Greed on the Grill: A 3D Printed Food Stacking Ballance Game

Gerse profile image

Gerse

20